Tribochemical Characterization and Tribocorrosive Behavior of CoCrMo Alloys: A Review.

Orthopedic implants first started out as an all-metal hip joint replacement. However, poor design and machinability as well as unsatisfactory surface finish subjected the all-metal joint replacement to being superseded by a polyethylene bearing. Continued improvement in manufacturing techniques together with the reality that polyethylene wear debris can cause hazardous reactions in the human body has brought about the revival of metal-on-metal (MOM) hip joints in recent years. This has also led to a relatively new research area that links tribology and corrosion together. This article aims at reviewing the commonly used tribochemical methods adopted in the analysis of tribocorrosion and putting forward some of the models and environmental factors affecting the tribocorrosive behavior of CoCrMo alloys, a widely-used class of biomaterial for orthopedic implants.

Mechanical, tribological and biological properties of novel 45S5 Bioglass® composites reinforced with in situ reduced graphene oxide.

45S5 Bioglass® (45S5) is one of the most widely used biomaterials in ceramic-based bone graft substitutes by virtue of its excellent biocompatibility and bioactivity. However, the fracture toughness and wear resistance of 45S5 have to be improved to extend its applications in load bearing orthopedic implants. The current study reports the first use of graphene nanoplatelet (GNP) to enhance the fracture toughness and wear resistance of 45S5. Composite powders with four different loadings of graphene oxide (GO), i.e. 0, 0.1, 0.5 and 1wt%, were sintered by spark plasma sintering (SPS) at a relatively low temperature of 550°C, during which in situ thermal reduction of GO took place. It was found that by adding 0.5wt% GO to the 45S5 powder, the fracture toughness of the sintered pellets was increased by 130.2% while friction coefficient and specific wear rate were decreased by 21.3% and 62.0%, respectively. Furthermore, the viability of MG63 cells grown on the GNP-incorporated pellets was comparably high to that of the cells grown on the pure 45S5 pellets. As compared with the pure 45S5 leachates, the media conditioned by the GNP/45S5 pellets fabricated from the composite powder with 1wt% GO could enhance both the proliferation and viability of MG63 cells. It is thus envisioned that the GNP-reinforced 45S5 is a highly promising material for fabricating mechanically strong and biocompatible load-bearing bone implants.

Development of sol-gel icephobic coatings: effect of surface roughness and surface energy.

Sol-gel coatings with different roughness and surface energy were prepared on glass substrates. Methyl triethoxysilane (MTEOS), 3-Glycidyloxypropyl trimethoxysilane (GLYMO) and fluoroalkylsilane (FAS) were used to obtain a mechanically robust icephobic coating. Different amount of hydrophobic silica nano particles was added as fillers to introduce different roughness and surface energy to the coatings. The microstructure, roughness, and surface energy, together with elemental information and surface chemical state, were investigated at room temperature. The contact angle and sliding angle were measured at different temperatures to correlate the wetting behavior at low temperature with the anti-icing performance. The ice adhesion shear strength was measured inside an ice chamber using a self-designed tester. The factors influencing the ice adhesion were discussed, and the optimum anti-icing performance found in the series of coatings. It was found that lower surface energy leads to lower ice adhesion regardless of the roughness, while the roughness plays a more complicated role. The wetting behavior of the droplet on surface changes as temperature decreases. The anti-icing performance is closely related to the antiwetting property of the surfaces at subzero temperatures.

Graphene ultrathin film electrode for detection of lead ions in acetate buffer solution.

Few-layer graphene ultrathin films were synthesized via solid-state carbon diffusion from amorphous carbon (a-C) thin layers sputtering coated on Si substrates with or without a SiO(2) layer, which an a-C layer was covered by a nickel (Ni) layer as a catalyst. When the Ni/a-C bilayer coated samples were heated at 1000°C the carbon (C) atoms from the a-C layers diffused into the top Ni layers to form a C rich surface. Upon rapid cooling, the C atoms accumulated on the surface of the Ni layers and formed graphene ultrathin films through nucleation and growth processes. The formation of graphene ultrathin films was confirmed by Raman spectroscopy, high resolution transmission electron microscopy (HR-TEM), electron diffraction, field-emission scanning electron microscopy (FE-SEM) and 4-point probe. The synthesized graphene ultrathin films were used as working electrodes for detection of trace heavy metal ions (Pb(2+), as low as 7 nM) in acetate buffer solutions (pH 5.3) using square wave anodic stripping voltammetry (SWASV). The effects of substrate surface condition and Ni layer thickness on the structure and electrochemical properties of graphene ultrathin film electrodes were investigated in detail. Compared to conventional diamond-like carbon (DLC) electrodes, the graphene electrodes developed in this study had better repeatability, higher sensitivity and higher resistance to passivation caused by surface active species.

Micro-DSC and rheological studies of interactions between methylcellulose and surfactants.

The effects of a cationic surfactant, cetyltrimethylammonium bromide (CTAB), on the gelation of methylcellulose (MC) in aqueous solutions have been investigated by micro differential scanning calorimetry (micro DSC) and rheology. Methylcellulose had a weight average molecular weight of 310,000 and a degree of substitution of 1.8. The concentration of MC was kept at 0.5 wt % (0.016 mM) and 1 wt % (0.032 mM), and the concentration of CTAB in the MC solutions was varied from 0 to 0.6 wt % (16.5 mM). Upon heating, a single endothermic peak, which is due to the hydrophobic association and gelation of MC, shifts to lower temperatures with increasing CTAB for CTAB < or = CMC (0.93 mM or 0.034 wt %), and then it shifts to higher temperatures lineally with CTAB for CTAB > CMC. At the same time, the endothermic enthalpy decreases with increasing CTAB concentration. Even though CTAB shows a significant "salt-in" effect on the gelation of MC, it does not affect the pattern of the sol-gel transition as well as the gel strength of MC. At the highest concentration of CTAB, 0.60 wt %, MC is still able to form a gel. At a given ratio of CTAB/MC, the effect of CTAB on MC becomes stronger when the MC concentration is lower. The results for the MC-CTAB system are compared with an ionic surfactant, SDS and the significant differences in affecting the gelation of MC between two surfactants are recognized.

Release of theophylline from polymer blend hydrogels.

Polymer blending is a simple yet attractive method to obtain combined physical and mechanical properties of polymers. In this paper, three types of blend hydrogels were prepared, each by physically blending two different natural polymers, and a model drug, theophylline (TPH), was immobilized into these hydrogels for the studies of drug release. The release profiles of TPH from various types of hydrogels were determined by UV-vis absorption measurement at 272 nm. The experimental results show that the releases of TPH from these hydrogels are dependent upon the composition of the hydrogel, the type of component, the possible interactions between two component polymers, as well as external temperature. All the release profiles clearly demonstrate a temperature effect. Among the three blend hydrogels, the slowest release was observed from the blend hydrogel of gelatin and agar with a weight ratio of 1:1. The drug release patterns and release mechanisms have been discussed by considering the possible molecular interactions and gel network structures.